1、打开石材雕刻机雕刻编程软件并编程雕刻路径：我们举例说明，如果刻字，那么先用文泰软件排好版，然后通过2D、3D、割，在弹出的对话框里输入深度、重叠率、行距等参数，然后让电脑运算。如果加工浮雕，先用ARTCAM或者精雕通过文件或者模型图片生成浮雕，然后确定尺寸，通过填好每项加工参数，电脑开始计算。路径生成后，会在字或者模型上生成带颜色的线，也就是我们常说的刀具路径。
1. Open the engraving programming software of stone engraving machine and program the engraving path: for example, if engraving, first arrange the version with Wentai software, and then input the parameters such as depth, overlap rate and line spacing in the pop-up dialog box through 2D, 3D and cutting, and then let the computer calculate. If processing relief, first use ArtCAM or precision carving to generate relief through files or model pictures, then determine the size, and start calculation by filling in each processing parameter. After the path is generated, colored lines will be generated on the word or model, which is often called tool path.
2、输出雕刻路径并输入雕刻机控制系统软件：在文泰、精雕、ARTCAM等软件里输出文件，如果是雕刻机控制系统不能支持的格式，还需要转换。常用的程序格式有nc、mmg等。
2. Output engraving path and input engraving machine control system software: output files in Wentai, Jingdiao, ArtCAM and other software. If it is a format that cannot be supported by engraving machine control system, it needs to be converted. The commonly used program formats are NC, MMG, etc.
3、检查机器并正确固定工件：看机器台面上是否有杂物，尤其是石材颗粒、大面积的石粉、砂子等，要注意清理，否则容易影响材料的平面度。造成深浅不一(解决不平问题可以访问我们的查看有关石材雕刻机调平系统又称刻字宝的说明)。
3. Check the machine and fix the workpiece correctly: check whether there are sundries on the machine table, especially stone particles, large-area stone powder, sand, etc. pay attention to cleaning, otherwise it is easy to affect the flatness of the material. Cause different depth (to solve the problem of unevenness, you can visit our official website to see the instructions on the leveling system of stone carving machine, also known as engraving treasure).
将工件按排版编程软件里的放置方向，看横向还是竖向放置材料。注意材料和机器走向轴方向平行，不要放偏了。
Place the workpiece according to the placement direction in the typesetting programming software to see whether the material is placed horizontally or vertically. Note that the material is parallel to the axis of the machine, and do not deviate.
用压板固定材料，一般固定方式有压和顶两种。如果是用压板压的话，注意不要压在材料的加工部分，防止机器撞车、撞刀。
Fix the material with pressing plate. Generally, there are two fixing methods: pressing and jacking. If the pressing plate is used, be careful not to press it on the processing part of the material to prevent the machine from crashing and hitting the knife.
4、确定工件坐标系原点，也就是我们常说的对刀。分别将机器的各个轴原点对齐原点，然后数据归零或者输入相应坐标系坐标值。
4. Determine the origin of workpiece coordinate system, that is, we often say tool setting. Align the origin of each axis of the machine with the origin respectively, and then return the data to zero or enter the coordinate value of the corresponding coordinate system.
5、检查喷水、水循坏，调整机器转速和进给速度，并在石材雕刻机控制系统软件里进行仿真，如果是维宏系统的话，按F8即可。查看仿真无误，再按F8推出仿真。
5. Check the water spray and water circulation, adjust the machine speed and feed speed, and simulate it in the control system software of stone carving machine. If it is Weihong system, press F8. Check that the simulation is correct, and then press F8 to launch the simulation.
